お問い合わせ
Blog >> Blog Details Page

Multimeter Measurements Explained

Posted:05:36 PM December 08, 2023 writer: The Engineering Knowledge

Introduction

The multimeter is an electrical device used in electronic projects and electrical systems to measure the different electrical parameters. With the use of this meter, anyone has to get the required valve of electrical systems. The function of this meter is based on the Ohm Law which is a combination of voltage, current, and resistance. In this post, we will cover the basics of this meter and will discuss its different functions and proper function understanding. So let's get started!

What is a Multimeter?

The multimeter is considered the main part of the electrical system. It is a known versatile device due to having features to measure different electrical through a single unit so preferred by any engineer or electronic student. There are two main types of multimeter first the digital multimeter and second the analog multimeter.  A digital multimeter comes with a digital display that makes it to easy read and offers correct electrical values. While in an analog meter, there is a need for a connected dial to provide the measured values. Due to easy use and high accuracy, digital multimeters are used, but analog multimeters are used for variation in measurements.

The main function of the multimeter is to measure voltage. it can used to measure both AC and DC voltage. To measure volts meter is connected to the circuit by making the connection of its red and black probes that are positive and negative. So to get accurate values and follow the safety measures during the use of meter are important.

DC Voltage Measurement

DC voltage measurement is a very common value measured from a multimeter. The DC voltage calculation feature of the meter is used to find the value of the electrical potential difference between two points in the circuit where the DC current is flowing.  Potential difference is measured in volts. For measuring the DC voltage set the DC V mode on the meter. Then connect the negative terminal of the circuit with the INPUT LO connection of the meter and the positive part of the circuit with the INPUT HI of the meter, then on the supply connected with the circuit results current flow is measured in the circuit on the meter.

AC voltage Measurement

The process of measuring the AC volts on a meter is the same as the DC volts measured. However, the difference is that a measuring alternating current, AC mode of the meter is used to connect with the circuit. AC voltage is also measured in Volt units. Before measuring ac voltage set the meter at AC V mode and connect probes. Connect the positive terminal of the circuit with INPUT HI and the negative terminal to INPUT LO. Then the power supply current flowing through the circuit will provide the voltage of the circuit on the meter

Get Instant PCB Online Quote

Measuring Resistance

There are different methods used to measure the resistance of the circuit through the use of a multimeter based on the accuracy required in measured values.  Multiemer finds the value of circuit resistance by providing the small value of current in a circuit and then calculates the value of voltage loss in the circuit. The current given to the circuit is known so voltage loss measured in the circuit is used to measure the value of resistance with the use of OHM law that is V= IR. When the circuit is connected to the meter the probe wires also have some resistance that is added to the circuit's measured resistance and made different to find the accurate value of resistance. So there are two other techniques used to measure the accurate resistance

Wire resistance measurement

If you need highly accurate resistance measurement. Then use 4 wire resistance measurement configuration. There are two extra probes used for this configuration, so it is known as 4 wire. Two probes are used to give current to the circuit and the other two measure voltage in the circuit. This process avoids the high value of voltage losses due to probe wire resistance, as it provides the accurate voltage value and resistance measured.

For making a 4-wire resistance arrangement with the use of a benchtop meter choose the ohm mode on the meter and press this button more than one time to arrange a four-wire mode. Connect the first two probes with INPUT high and INPUT LO and the other two with SENSE HI and SENSE Low ports of the meter. Make sure the circuit is in the off state and then probe the required part of the circuit with the use of HI probes on a positive part of the circuit and LO probes on the negative part of the circuit.

DC current

DC current measurement is helpful to find the single direction flow of current in the circuit its measuring unit is ampere. To measure the current in the circuit it must be open and then connected with a meter to measure the current. This arrangement helps the current flow in the meter. For measuring the current meter connected in series combination of resistance and voltage is measured with the parallel configuration of the meter with the circuit.

If you are measuring DC current with the use of a benchtop meter choose I DC mode on the meter. Make the connection of the positive probe of the circuit with the mA port of the meter to measure the small value of the current and use the 10A port for measuring the high current in the circuit. Attach negative probe with INPUT LO port. After making the right connection supply the circuit and measure the value of the DC.

AC current

AC current is measured in an AC system that continuously varies the directions. its measuring unit is ampere. As we measured DC through the series connection of the meter in the circuit AC also connects the meter in the circuit in a series combination. To measure the AC current set I AC mode of mete and make the connection of the positive part of a circuit with the mA port of the meter to measure the small value of current and for high current use 10A port. Connect the negative probe with the INPUT LO port then supply the circuit and measure the value of ac curent. Try to avoid common mistakes normally new learners use mA for measuring larger current values that will affect the meter working so for measuring 200mA current use the 10A port to affect the fuse connected in the meter.

Additional Multimeter Measurements

Diode Test

The multimer can be used to measure diode losses in forward-biased conditions of the diode. In the forward biasing state positive leads of the source connect with the anode of the diode and negative with the cathode of the diode. To find the value of the diode voltage losses meter gives the same value of voltage across the probes and increases voltage values till there is an electrical connection between two probes. Diode voltage losses are measured in DC volts.

For measuring the diode losses set the diode test mode of the meter by pressing the button that has the diode symbol. Attach the positive probe with the INPUT HI port and the negative probes with the INPUT LO port. Make sure the circuit is not connected to the power supply. Now connect the power supply with the diode according to the required polarity measures voltage losses

Frequency

With the use of a multimeter, we can measure the frequency of the AC signal. Frequency is a measurement of cycles repeated in one second. If the sine wave is repeated 20 times in one second will have a twenty-hertz frequency. Input frequency on the meter can change so before measuring a high value of frequency check that the meter can measure the frequency value. Similar to voltage we frequency measured in parallel configuration of the circuit.

To find the value of high frequency with high accuracy use the dedicated frequency counter. To measure the frequency with the meter set the meter to FREQ mode then attach the opposite probe with the INPUT HI port and the negative probe with the INPUT LO port. Make sure the supply is connected with the circuit where the frequency is measured.

Different Types of Multimeters

Type

Description

Advantages

Disadvantages

Analog

There is a moving coil meter and pointer used to show the measured value

Less cost, not needed battery, it measures variations in readings

it needed a high interpretation of scale and was less accurate than a digital multimeter

Digital

it has an LCD display where measured values are shown

High accuracy, measures positive and negative values, easy to read

it uses a battery and is higher cost than an analog meter

Fluke

it is a digital multimeter that comes with some additional features like humidity measurement, duty cycle, frequency pressure, and temperature measurement

Correct, durable, versatile

High prices than other digital multimeters

Clamp

it is used to find the value of the current without making contact with the circuit and it is used around the wires to measure the value

its main feature is to measure current without affecting the circuit

It has lower accuracy than other meters and does not measure resistance or voltage

Autoranging

its main feature is to set an accurate range of values being measured

It does not need any setting of range and is easily used

Its prices are higher than other digital multimeters

 

Get Instant Online Quote

How to measure resistor with a multimeter

Set Multimeter:

  • On the meter check that it is set at the resistance symbol which is Omega (Ω)

Set Range:

  • Select the proper resistance value on the meter. If you are not sure about the value of resistance then choose a high range and move downward

Remove Resistor:

  • Make sure that the resistor is not connected to any circuit. If it is connected with any component of the circuit remove its one pin to separate it

 Connect the Probes:

  • Now get the meter probes to connect red and black probes with resistor leads. As we have to measure resistance so not consider the polarity of probes

 Read the Display:

  • At meter value of measured resistance can seen in ohms units. If the value is high or on LCD there is OL mentioned that is overloaded then increase the meter range

The value resistance is measured through a digital multimeter by sending a small known voltage through the resistor and then measuring the required current. Here process explained

  • Voltage Source:
    • There is a small voltage produced by the battery connected to the meter. This voltage is constant and has a known value.
  • Ohm's Law:
    • OHM law defines the relation between current, resistance, and voltage.  For measuring resistance meter gives voltage about the resistor and measures the resulting current flowing
  • Current Flow:
    • The known voltage passes resistors and current flow in resistance according to its resistance.
  • Measuring the Current:
    • Current passing through resistor measured. As the voltage value is known and the current value is also calculated using home law we can find resistance R=V/I
  • Display  Resistance value:
    • Resistance measured shown on the screen of the meter

Conclusion:

The multimeter is a very important device in the electronic field to measure different parameters of a system like resistance, voltage, and current. With the use of this meter, we can measure AC, DC voltage, AC, DC and it is used for diode testing and can find the value of frequency. Now it has become very common in our system and every engineer must have a proper understanding to find different values of electrical system parameters.

You may also be interested in...

What is the Difference between an Analog Multimeter and a Digital Multimeter?

What’s The Difference Between Watts And Volt-Amperes?

Free PCB Assembly Offer is Now Live: Experience Reliable PCB Assembly from HQ NextPCB

HQ NextPCB Introduces New PCB Gerber Viewer: HQDFM Online Lite Edition

  • PCB
    Prototype
  • PCB
    Assembly
  • SMD
    Stencil

Dimensions: (mm)

×

Quantity: (pcs)

5
5
10
15
20
25
30
40
50
75
100
120
150
200
250
300
350
400
450
500
600
700
800
900
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
9000
10000

Other Quantities:(quantity*length*width is greater than 10㎡)

OK

Layers:

Thickness:

Quote now